View NL17SZ86DFT2G_470270.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

NL17SZ86 Single 2-Input Exclusive-OR Gate
The NL17SZ86 is a high performance single 2-input Exclusive-OR Gate operating from a 2.3 V to 5.5 V supply.
Features http://onsemi.com MARKING DIAGRAM
5 1 SC70-5/SC-88A/SOT-353 DF SUFFIX CASE 419A d = Date Code
* * * * * * * * *
Extremely High Speed: tPD 2.4 ns (typical) at VCC = 5.0 V Designed for 1.65 V to 5.5 V VCC Operation Over Voltage Tolerant Inputs LVTTL Compatible - Interface Capability with 5.0 V TTL Logic with VCC = 3 V LVCMOS Compatible 24 mA Balanced Output Sink and Source Capability Near Zero Static Supply Current Substantially Reduces System Power Requirements Replacement for NC7SZ86 Pb-Free Package is Available
L8d
Pin 1
PIN ASSIGNMENT
1 2 3 4 IN B IN A GND OUT Y VCC
IN B
1
5
VCC
5
IN A
2
FUNCTION TABLE
Inputs Output B L H L H Y L H H L
GND
3
4
A OUT Y L L H H
Figure 1. Pinout (Top View)
IN A IN B
=1
ORDERING INFORMATION
OUT Y
See detailed ordering and shipping information in the package dimensions section on page 4 of this data sheet.
Figure 2. Logic Symbol
(c) Semiconductor Components Industries, LLC, 2005
1
January, 2005 - Rev. 3
Publication Order Number: NL17SZ86/D
NL17SZ86
MAXIMUM RATINGS
Symbol VCC VI VO IIK IOK IO ICC IGND TSTG TL TJ qJA PD MSL FR ILatchup ESD DC Supply Voltage DC Input Voltage DC Output Voltage, Output in High or Low State (Note 1) DC Input Diode Current DC Output Diode Current DC Output Sink Current DC Supply Current per Supply Pin DC Ground Current per Ground Pin Storage Temperature Range Lead Temperature, 1 mm from Case for 10 Seconds Junction Temperature under Bias Thermal Resistance Power Dissipation in Still Air at 85C Moisture Sensitivity Flammability Rating Latchup Performance ESD Classification Oxygen Index: 28 to 34 Above VCC and Below GND @ 85C (Note 3) Human Body Model (Note 4) Machine Model (Note 5) Charge Device Model (Note 6) (Note 2) VI < GND VO < GND Parameter Value *0.5 to )7.0 -0.5 V v VI v +7.0 V -0.5 V to VCC + 0.5 *50 *50 $50 $100 $100 *65 to )150 260 )150 350 150 Level 1 UL 94 V-0 @ 0.125 in $500 Class 1B Class B N/A mA Unit V V V mA mA mA mA mA C C C C/W mW
Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected. 1. IO absolute maximum rating must be observed. 2. Measured with minimum pad spacing on an FR4 board, using 10 mm-by-1 inch, 2-ounce copper trace with no air flow. 3. Tested to EIA/JESD78 4. Tested to EIA/JESD22-A114-A, rated to EIA/JESD22-A114-B. 5. Tested to EIA/JESD22-A115-A, rated to EIA/JESD22-A115-B. 6. Tested to JESD22-C101-A.
RECOMMENDED OPERATING CONDITIONS
Symbol VCC VI VO TA Dt/DV Supply Voltage Input Voltage Output Voltage Operating Free-Air Temperature Input Transition Rise or Fall Rate VCC = 2.5 V $0.2 V VCC = 3.0 V $0.3 V VCC = 5.0 V $0.5 V Parameter Operating Data Retention Only (Note 7) (HIGH or LOW State) Min 1.65 1.5 0 0 *40 0 0 0 Max 5.5 5.5 5.5 5.5 )85 20 10 5 Unit V V V C ns/V
7. Unused inputs may not be left open. All inputs must be tied to a high- or low-logic input voltage level.
http://onsemi.com
2
NL17SZ86
DC ELECTRICAL CHARACTERISTICS
VCC (V) 1.65 to 1.95 2.3 to 5.5 1.65 to 1.95 2.3 to 5.5 IOH = 100 mA IOH = -3 mA IOH = -8 mA 8A IOH = -12 mA IOH = -16 mA IOH = -24 mA 24 IOH = -32 mA 32 A IOL = 100 mA IOL = 3 mA IOL = 8 mA A IOL = 12 mA IOL = 16 mA IOL = 24 mA IOL = 32 mA A VIN = VCC or GND VIN = VCC or GND 1.65 to 5.5 1.65 2.3 23 2.7 27 3.0 3.0 4.5 45 1.65 to 5.5 1.65 2.3 23 2.7 27 3.0 3.0 4.5 45 0 to 5.5 5.5 VCC - 0.1 1.29 1.9 19 2.2 22 2.4 2.3 3.8 38 VCC 1.8 2.1 21 2.4 24 2.7 2.5 4.0 40 0.08 0.20 0 20 0.22 0 22 0.28 0.38 0.42 0 42 0.1 0.24 0.3 03 0.4 04 0.4 0.55 0.55 0 55 $0.1 1 TA = 255C Min 0.75 VCC 0.7 VCC 0.25 VCC 0.3 VCC VCC - 0.1 1.29 1.9 19 2.2 22 2.4 2.3 3.8 38 0.1 0.24 0.3 03 0.4 04 0.4 0.55 0.55 0 55 $1.0 10 Typ Max *405C v TA v 855C Min 0.75 VCC 0.7 VCC 0.25 VCC 0.3 VCC Max Unit V V V
Symbol VIH VIL VOH
Parameter High-Level Input Voltage Low-Level Input Voltage High-Level Out ut Voltage Output VIN = VIL or VIL
Condition
VOL
Low-Level Output Voltage Out ut VIN = VIH
V
IIN ICC
Input Leakage Current Quiescent Supply Current
mA mA
AC ELECTRICAL CHARACTERISTICS tR = tF = 3.0 ns
Symbol tPLH tPHL Parameter Propagation Delay (Figure 3 and 4) Condition RL = 1 MW, CL = 15 pF RL = 1 MW, CL = 15 pF RL = 1 MW, CL = 15 pF RL = 1 MW, CL = 15 pF F RL = 500 W, CL = 50 pF RL = 1 MW, CL = 15 pF F RL = 500 W, CL = 50 pF VCC (V) 1.65 1.8 2.5 $ 0.2 3.3 $ 0.3 5.0 $ 0.5 TA = 255C Min 2.0 2.0 1.2 0.8 1.2 0.5 0.8 Typ 6.9 5.7 4.1 3.0 3.8 2.2 2.9 Max 13.8 11.5 7.0 4.8 5.4 3.5 4.2 *405C v TA v 855C Min 2.0 2.0 1.2 0.8 1.2 0.5 1.0 Max 14.5 12 7.5 5.2 5.9 3.8 4.6 Unit ns
CAPACITIVE CHARACTERISTICS
Symbol CIN CPD Input Capacitance Power Dissi ation Ca acitance Dissipation Capacitance (Note 8) Parameter Condition VCC = 5.5 V, VI = 0 V or VCC 10 MHz, VCC = 3.3 V, VI = 0 V or VCC 10 MHz, VCC = 5.5 V, VI = 0 V or VCC Typical 7.0 9 11 Unit pF pF F
8. CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation: ICC(OPR) = CPD VCC fin + ICC. CPD is used to determine the no-load dynamic power consumption; PD = CPD VCC2 fin + ICC VCC.
http://onsemi.com
3
NL17SZ86
tf = 3 ns
90% 90% 50% 10%
tf = 3 ns VCC or GND VCC OUTPUT INPUT GND RL CL
INPUT A and B
50% 10%
tPHL
tPLH VOH A 1-MHz square input wave is recommended for propagation delay tests. VOL
OUTPUT Y
50%
50%
Figure 3. Switching Waveform
Figure 4. Test Circuit
DEVICE ORDERING INFORMATION
Device Nomenclature Device Order Number NL17SZ86DFT2 Logic Circuit Indicator NL No. of Gates per Package 1 Temp Range Identifier 7 Device Function 86 Package Suffix DF Tape and Reel Suffix T2 Package Type SC70-5/ SC-88A/ SOT-353 SC70-5/ SC-88A/ SOT-353 (Pb-Free) Tape and Reel Size 178 mm, 3000 Unit
Technology SZ
NL17SZ86DFT2G
NL
1
7
SZ
86
DF
T2
178 mm, 3000 Unit
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D.
http://onsemi.com
4
NL17SZ86
PACKAGE DIMENSIONS
SOT-353 DF SUFFIX 5-LEAD PACKAGE CASE 419A-02 ISSUE G
A G
5
4
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. 419A-01 OBSOLETE. NEW STANDARD 419A-02. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS.
S
1 2 3
-B-
DIM A B C D G H J K N S
D 5 PL
0.2 (0.008)
M
B
M
N J C
INCHES MIN MAX 0.071 0.087 0.045 0.053 0.031 0.043 0.004 0.012 0.026 BSC --- 0.004 0.004 0.010 0.004 0.012 0.008 REF 0.079 0.087
MILLIMETERS MIN MAX 1.80 2.20 1.15 1.35 0.80 1.10 0.10 0.30 0.65 BSC --- 0.10 0.10 0.25 0.10 0.30 0.20 REF 2.00 2.20
H
K
SOLDERING FOOTPRINT*
0.50 0.0197
0.65 0.025 0.65 0.025 0.40 0.0157
1.9 0.0748
SCALE 20:1
mm inches
*For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
5
NL17SZ86
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 61312, Phoenix, Arizona 85082-1312 USA Phone: 480-829-7710 or 800-344-3860 Toll Free USA/Canada Fax: 480-829-7709 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center 2-9-1 Kamimeguro, Meguro-ku, Tokyo, Japan 153-0051 Phone: 81-3-5773-3850 ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder For additional information, please contact your local Sales Representative.
http://onsemi.com
6
NL17SZ86/D

▲Up To Search▲

Price & Availability of NL17SZ86DFT2G

	To Download NL17SZ86DFT2G Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .